style="font-size:15px;"> F. logging trap warnings
G. logging trap alerts
5. IPv6 unicast routing is running on the Corp router. Which of the following addresses would show up with the show ipv6 int brief command?
A. FF02::3c3d:0d: bdff:fe3b:0d80
B. FE80::3c3d:2d: bdff:fe3b:0d80
C. FE80::3c3d:0d: bdff:fe3b:0d80
D. FE80::3c3d:2d: ffbd:3bfe:0d80
6. A host sends a type of NDP message providing the MAC address that was requested. Which type of NDP was sent?
A. NA
B. RS
C. RA
D. NS
7. Each field in an IPv6 address is how many bits long?
A. 4
B. 16
C. 32
D. 128
8. What does the command routerA(config)#line cons 0 allow you to perform next?
A. Set the Telnet password.
B. Shut down the router.
C. Set your console password.
D. Disable console connections.
9. Which two statements describe the IP address 10.16.3.65/23? (Choose two.)
A. The subnet address is 10.16.3.0 255.255.254.0.
B. The lowest host address in the subnet is 10.16.2.1 255.255.254.0.
C. The last valid host address in the subnet is 10.16.2.254 255.255.254.0.
D. The broadcast address of the subnet is 10.16.3.255 255.255.254.0.
E. The network is not subnetted.
10. On which interface do you configure an IP address for a switch?
A. int fa0/0
B. int vty 0 15
C. int vlan 1
D. int s/0/0
11. Which of the following is the valid host range for the subnet on which the IP address 192.168.168.188 255.255.255.192 resides?
A. 192.168.168.129–190
B. 192.168.168.129–191
C. 192.168.168.128–190
D. 192.168.168.128–192
12. Which of the following is considered to be the inside host’s address after translation?
A. Inside local
B. Outside local
C. Inside global
D. Outside global
13. Your inside locals are not being translated to the inside global addresses. Which of the following commands will show you if your inside globals are allowed to use the NAT pool?
A. debug ip nat
B. show access-list
C. show ip nat translation
D. show ip nat statistics
14. How many collision domains are created when you segment a network with a 12-port switch?
A. 1
B. 2
C. 5
D. 12
15. Which of the following commands will allow you to set your Telnet password on a Cisco router?
A. line telnet 0 4
B. line aux 0 4
C. line vty 0 4
D. line con 0
16. Which router command allows you to view the entire contents of all access lists?
A. show all access-lists
B. show access-lists
C. show ip interface
D. show interface
17. What does a VLAN do?
A. Acts as the fastest port to all servers
B. Provides multiple collision domains on one switch port
C. Breaks up broadcast domains in a layer 2 switch internetwork
D. Provides multiple broadcast domains within a single collision domain
18. If you wanted to delete the configuration stored in NVRAM, choose the best answer for the Cisco objectives.
A. erase startup
B. delete running
C. erase flash
D. erase running
19. Which protocol is used to send a destination network unknown message back to originating hosts?
A. TCP
B. ARP
C. ICMP
D. BootP
20. Which class of IP address provides 15 bits for subnetting?
A. A
B. B
C. C
D. D
21. There are three possible routes for a router to reach a destination network. The first route is from OSPF with a metric of 782. The second route is from RIPv2 with a metric of 4. The third is from EIGRP with a composite metric of 20514560. Which route will be installed by the router in its routing table?
A. RIPv2
B. EIGRP
C. OSPF
D. All three
22. Which one of the following is true regarding VLANs?
A.
