TRICKS OF THE TRAIL
Buying a Pack When you go to the store and try on a pack, the salesperson will help you adjust it, and it will feel great. Then she will give you a few sandbags (25–30 pounds or 11–13 kilograms) to add some weight. Chances are it will still feel good. The real test is when you get home and try to carry 50 to 70 pounds (22–31 kilograms). Make sure that the store will take the pack back if it doesn’t feel right. I bought a pack once without doing this test until I hit the trail. With 60 pounds in the pack, the hip belt slipped off my butt and I ended up carrying most of the weight on my shoulders. I hiked in discomfort for days.
It is essential to have a pack that fits properly. The major measurements are your spine length, waist size, and shoulder width to get a pack the correct length and one with the correct size hip belt and shoulder straps. Packs vary from company to company, so check the manufacturer’s instructions for both fitting and loading. Many packs come with different size hip belts and/or shoulder straps and some are specifically designed for women’s bodies. The idea behind a frame pack is to have the frame transfer most of the weight to your legs through the hip belt. Therefore, when fitting a pack, the place to start is with the hip belt. Here are some general fitting guidelines:
Put on the pack and adjust the hip belt to fit your hips. Wear the hip belt on the hip bones just underneath the rib cage. The center of the hip belt is about at the crest of your pelvis. The buckle will be about at your navel. Wearing the hip belt higher transfers weight onto major muscle groups. Wearing the belt too low on the hips can compress arteries and nerves and lead to poor circulation and numbness in the legs.
With the hip belt on and properly positioned, tighten the shoulder straps and note their position. Some packs will allow you to adjust the height at which the shoulder straps attach to fine-tune your fit. For an external-frame pack the straps should come off the frame about even with the top of your shoulders. If the straps drop too far down, the pack is too small, and too much weight will be pulled onto your shoulders. If the straps go too far up, the pack is too large, and too little weight will go onto your shoulders. For an internal-frame pack the frame stays or frame structure should extend 2 to 4 inches above your shoulders. The shoulder straps should follow the contour of your shoulders and join the pack approximately 2 inches (5 centimeters) below the top of your shoulders. The position of the shoulder harness can usually be adjusted. The lower ends of the straps should run about 5 inches (12.7 centimeters) below your armpits. On both types of packs be sure the width of the shoulder straps is positioned so that they neither pinch your neck nor slip off your shoulders. On the shoulder straps you may find load lifters that connect to the pack at about ear level and connect to the shoulder straps in front of your collarbone. These help pull the top of the pack onto your shoulders.
Some internal-frame packs allow you to bend the frame stays to adjust them to match the curvature of your back.
In both types of packs the sternum strap should cross your chest below your collarbone. If the pack is properly fitted, you can adjust the load lifters and other fine-tuning straps to make the pack hug your back. Adjustments can also be made while hiking, periodically shifting the weight distribution to other muscle groups, which makes hiking less tiring.
Loading an External-Frame Pack
The major consideration in loading a pack is how best to distribute the weight. There are two basic principles: for trail hiking over generally flat ground, the weight of the pack should be high and relatively close to the body. The heavier items should sit between your shoulder blades. For consistently steep or rough terrain, carry the weight lower to give you better balance and avoid falls from having a higher center of gravity. In this case, heavier things should be placed more toward the middle of your back. To achieve either arrangement, load the heavier, bulky items into the large top compartment in the position where you want most of the weight. Then fill this and the remaining compartments with lighter items. Tents and tarpaulins can be lashed to the extender bars at the top of the pack and sleeping bags can usually be lashed to the frame at the bottom of the pack. In either case, the horizontal weight distribution should be balanced so that the left side of the pack is in balance with the right. A woman’s center of gravity is generally lower than a man’s. So, for women, the heavier items should be placed close to the body but lower in the pack, as in the case for rough terrain, described above. Packs designed especially for women take this into account by lowering the pack bag on the frame. Load these packs as described above and then lash sleeping bags and tents or tarpaulins to the extender bars at the top of the packs.
Packing External- and Internal-Frame Packs
Loading an Internal-Frame Pack
Your gear will help form the structure of support for an internal-frame pack. For easy, level hiking, a high center of gravity is best. To achieve this, load bulky, light gear (e.g., your sleeping bag) low in the pack and stack heavier gear on top of it. For steeper terrain, a lower center of gravity is best because it lessens the chance of falls from a top-heavy pack. In this case, place heavier items a little lower in the pack and closer to your back than normal. Women may prefer this arrangement under all circumstances.
Stuff your clothes into the pack or pack items in stuff sacks rather than fold them. This serves to fill all the available space of the pack better so that things don’t shift around and allows you to get more into the pack.
The more common weight distribution (general trail hiking) has the lighter, bulkier items on the bottom: the sleeping bag and clothes. The heavier items such as food, stoves, and fuel go into the upper section or on top of the pack, with the heaviest items closest to the pack frame. A general rule is that 50 percent of the weight should be in the upper third of the pack.
For consistently steep or rough terrain, carry the weight lower to give you better balance.
The horizontal weight distribution should be balanced so that the left side of the pack is in balance with the right.
Your hip belt should have enough room to allow you to loosen or tighten it for different layers of clothing beneath. If the belt is too loose, socks or shirts can be inserted between the belt and your body. This adds an extra layer of padding to the belt as well, which may increase the comfort of the fit.
Avoid hanging things all over the outside of your pack—no one wants to listen to you clank and clang your way down the trail; also, all that junk can snag branches. If you find yourself having to tie things on all the time, either your pack is
