time to fill out the warranty postcard included in your meter kit, and then send it in. This will register your device with the company so you will be notifed of any recalls, problems, or special offers.
CHECKING YOUR BLOOD GLUCOSE WITH YOUR METER: THE BASIC STEPS
1. ASSEMBLE YOUR SUPPLIES.
Before you start, wash your hands with soap and water. Dry your hands with a paper towel or clean towel, rather than the used towel that has been hanging in the bathroom all week. Be sanitary. Make sure you have all of the materials you’ll need, including:
TIPS ON CLEANING
Antibacterial soap and water is the preferred method for cleaning a test site. Dry the area with a paper towel or let it air dry—no wiping or blowing germs and dust onto the area. Alcohol pads are fine to use, but if you have dry skin or irritated cuticles the alcohol may cause further drying and possible cracking. Additionally, the alcohol must be completely dry, or else you might end up knowing the glucose level of a mixture of alcohol and blood.
Antibacterial hand sanitizers should not be used to clean sites for blood glucose testing. These products may contain other chemicals, perfumes, or additives that could possibly give a false reading. Stick with plain ol’ soap and water.
2. TURN ON THE METER AND FOLLOW INSTRUCTIONS.
Follow the manufacturer’s directions for turning on your meter. If you plan to use the memory, ensure that the time and date are set correctly. Make sure you are not seeing any errors or problems on the screen. If the screen display is faint or blinking, consult the user’s manual to identify the problem—you may need a new battery, or it may be a sign of electrical malfunction. If you get an error message, once again, consult the user’s manual before testing or call the toll-free customer support number written on the back of the device for help. If the meter is having a problem, chances are the test result will not be accurate, so wait until the problem is resolved. You may also have to calibrate (set your meter to interpret the test strip results). Read your instruction booklet or call the manufacturer’s toll-free help number to learn how to do this important step.
3. INSERT A NEW TEST STRIP.
Follow the manufacturer’s instructions for inserting a strip. Handle the test strips with care, making sure they do not get wet or handled in the testing area before being inserted into the device. Do not use a strip that has fallen in the sink or been left out for more than few minutes.
4. PREPARE AND PRICK.
Prepare the testing site by increasing circulation for better blood flow. If you are testing your fingers, shake your fingers or pump your hand into a fist a few times. If you are using alternative-site testing, you may be instructed to rub the area to increase blood flow. Cold tissue may not have good blood flow—warm up the area before testing if you have been exposed to cold temperatures.
Prick the site with the lancet device. Once again, follow the manufacturer’s directions for using the lancet. To make testing more comfortable, try different sites to see what works best for you.
If you do not get the quantity you need, “milk” the finger by using your other hand to squeeze from the base of your finger to the tip. Hold your fingertip down (not up in the air) to let gravity help. Relax the finger—constricting the finger or being tense will restrict blood flow to the area. If you use your fingertips often (e.g., needle crafters, computer keyboarders, ball players, brick layers, musicians) and have tough skin, you may want to use the fourth or fifth fingers, which may be more supple.
FOR ALTERNATIVE-SITE TESTING
If you’re using a meter that allows alternative-site testing, follow the manufacturer’s directions and remember that getting a sample may take a little more time. The most important tip is timing—do not release pressure on the lancet device until the appropriate time has expired. Be patient; allow sufficient time for the sample to appear.
5. APPLY THE SAMPLE TO THE RECEIVING PART OF THE STRIP.
Too much blood may cause a false reading or error message to occur. Too little blood may cause a false reading, with the result being lower than your actual blood glucose count. Some strips can be reapplied if the first contact did not sufficiently coat the receiving part of the strip. Before trying a reapplication, read your user’s manual to find out if this is acceptable.
Blot the site with a cotton ball with slight pressure until bleeding stops. If you are a heavy bleeder or on blood-thinning medications, you may want to have several cotton balls on hand. You may also want to use a low-depth setting with your lancet device. If you bruise easy, try to wiggle your finger soon after the stick to encourage blood circulation. A bandage is usually not necessary unless you’d simply like to avoid getting blood on your clothes or other surfaces.
6. RECORD YOUR RESULT IN A BLOOD GLUCOSE DIARY.
If you did not get a diary from your meter company or your health care professional, make your own with a small spiral notebook. Record the time, date, and result. Make notes for any usual events such as illness, pain, skipped meals, special meals, missed medications, etc.
7. WRAPPING IT UP:
