EXERCISE 3F
INSTRUCTIONS:
1. Start a new file using template: acad.dwt (Inch) or acadiso.dwt (Metric).
2. Load Linetypes Zigzag, Gas_Line and Dashed (Refer to page 3-16).
3. Create 3 layers named Fence, Gas and Invisible. (Refer to page 3-15)
Assign the Name, Color, Linetype and Lineweight as shown above.
Note: Lineweights for metric users are: Zigzag = 0.5 mm, Gas-Line = 1.2 mm, Dashed = 0.25 mm.
4. Draw the LINES below using the new layers:
A. Select the layer
B. Select the Line command
C. Draw the lines approximately 5 inches [127 mm] long.
D. Ortho (F8) ON.
5. Save the drawing as: Ex-3F
EXERCISE 3G
INSTRUCTIONS:
1. Open Ex-3B
2. Open the Layer Properties Manager (Refer to page 3-10).
3. Change Transparency of the Object Line layer to 70 (Refer to page 3-14).
4. Select the Transparency status button to show or hide Transparency.
5. Save the drawing as: Ex-3G
Notes:
LEARNING OBJECTIVES
After completing this lesson, you will be able to:
1. Understand Object Snap.
2. Use Running Object Snap.
3. Use the Zoom options to view the drawing.
4. Change the Drawing Limits.
5. Select the Units of Measurement and Precision.
In Lesson 3 you learned about Increment Snap. Increment Snap enables the cursor to move in an incremental movement. So you could say your cursor is “snapping to increments” preset by you.
Now you will learn about Object Snap. If Increment Snap snaps to increments, what do you think Object Snap snaps to? That’s right; “objects”. Object snap enables you to snap to “objects” in very specific and accurate locations on the objects.
For example, the endpoint of a line or the center of a circle.
How to select from the Object Snap Menu
1. You must select a command, such as LINE, before you can select Object Snap.
2. While holding down the shift key, press the right mouse button The menu shown below should appear.
3. Highlight and press the left mouse button to select an Object Snap.
The following object snaps will be discussed in this Lesson:
Endpoint, Midpoint, Intersection, Center, Geometric Center, Quadrant, Tangent and Perpendicular. Refer to their descriptions on the next page.
The remaining object snaps will be discussed in future lessons.
Object Snap Definitions
Object snap is used when AutoCAD prompts you to place an object. Object snap allows you to place objects very accurately.
A step-by-step example of “How to use object snap” is shown on the next page.
Note: You may type the 3 bold letters shown rather than select from the menu.
| Snaps to the closest endpoint of a Line, Arc or polygon segment. Place the cursor on the object close to the end and the cursor will snap like a magnet to the end of the line. | |
| Snaps to the middle of a Line, Arc or Polygon segment. Place the cursor anywhere on the object and the cursor will snap like a magnet to the midpoint of the line. | |
| Snaps to the intersections of any two objects. Place the cursor directly on top of the intersection or select one object and then the other and Autocad will locate the intersection. | |
| Snaps to the center of an Arc, Circle or Donut. Place the cursor on the object, or at the approximate center location and the cursor will snap like a magnet to the center. | |
| Snaps to the centroid of any closed polylines and splines. Place the cursor anywhere on the object and the cursor will snap to the centroid of any closed polyline or spline. | |
| Snaps to a 12:00, 3:00, 6:00 or 9:00 o’clock location on a circle or ellipse. Place the cursor on the circle near the desired quadrant location and the cursor will snap to the closest quadrant. | |
