Advanced AutoCAD 2017. Cheryl R. Shrock

Чтение книги онлайн.

Читать онлайн книгу Advanced AutoCAD 2017 - Cheryl R. Shrock страница 17

Автор:
Жанр:
Серия:
Издательство:
Advanced AutoCAD 2017 - Cheryl R. Shrock

Скачать книгу

Type Plot <enter>

image

      D. Select Import... from the Page Setup drop down menu

      E. Find My Decimal Setup.dwt as follows:

      E1. Select Files of type: Template [.dwt]

      E2. Select My Decimal Setup.dwt

      E3. Select Open button.

image

      F. Select Plot Setup A from the Import Page Setups list.

      G. Select the OK button.

image

      H. Select Plot Setup A from the Page Setup drop down list.

      (Note: It was not there before. You just imported it in from My Decimal Setup.dwt)

image

      I. Review all the settings.

image

      J. Select Preview button.

      If the drawing appears as you would like it, press the Esc key and continue

      If the drawing does not look correct, press the Esc key and check all your settings, then preview again.

       Note: The Viewport will not appear in the Preview because it is on a no plot layer.

      K. Select the Apply to Layout button.

       (The settings are now saved to the layout tab for future use.)

      L. If your computer is connected to the plotter / printer selected, select the OK button to plot, then proceed to N.

      M. If your computer is not connected to the plotter / printer selected, select the Cancel button to close the Plot dialog box and proceed to N.

      N. Important: Save the file again as My Feet-Inches Setup

      O. You are almost done....continue on to 4F.

       CREATE A NEW DIMENSION STYLE

      1. Open My Feet-Inches Setup (If not already open)

      2. Select the Dimension Style Manager command.

image

      3. Select the NEW button.

image

      4. Enter DIM-ARCH in the “New Style Name” box.

      5. Select STANDARD in the “Start With:” box.

      6. Select Annotative box.

      7. Select the CONTINUE button.

      8. Select the Primary Units tab and change your settings to match the settings shown below.

image

      9. Select the Lines tab and change your settings to match the settings shown below.

image

      10. Select the Symbols and Arrows tab and change your settings to match the settings shown below.

image

      11. Select the Text tab and change your settings to match the settings shown below.

image

      12. Select the Fit tab and change your settings to match the settings shown below.

image

      13. Now select the OK button.

      Your new DIM-ARCH dimension style should now be in the list.

      14. Select the Set Current button to make your new style DIM-ARCH the style that will be used.

image

      15. Select the Close button

      16. Important: Save your drawing as My Feet-Inches Setup again.

      17. You are almost done. Now Save all of this work as a Template.

      a. Select Application Menu / Save As / AutoCAD Drawing Template

      b. Type: My Feet-Inches Setup

      c. Select the Save button.

       Note:

      Metric users may wish to create an Architectural Template the same as the Feet-Inches template. You can use the exact same principle used in this exercise but with the metric equivalents. Instead of opening the acad.dwt template described on page 4-2, use the acadiso.dwt template. For the Drawing Units use Length Type: Decimal. For the Insertion Scale use: Millimeters.

       LEARNING OBJECTIVES

       After completing this lesson, you will be able to:

      1. Create a Table.

      2. Insert a Table.

      3. Modify an existing Table.

      4. Insert a Block into a Table Cell.

      5. Insert a Formula into a Table Cell.

      6. Create

Скачать книгу