Marijuana Horticulture Fundamentals. K of Trichome Technologies
Чтение книги онлайн.
Читать онлайн книгу Marijuana Horticulture Fundamentals - K of Trichome Technologies страница 21
![Marijuana Horticulture Fundamentals - K of Trichome Technologies Marijuana Horticulture Fundamentals - K of Trichome Technologies](/cover_pre684671.jpg)
Use oscillating fans to keep air constantly circulating throughout the room.
Photos: K
The four inches of water at the bottom of the bucket will quickly fill with healthy white roots relaxing in the oxygen- and nutrient-rich water and absorbing all they need to thrive. Plants are grown vegetatively until they reach one foot tall, at which point they are switched to 12 on / 12 off (the flowering stage). The plants in these photos have been in the flowering stage for approximately two weeks; they will mature and finish flowering between two and three feet tall, requiring no stakes or nets to keep them up because of the shorter plant stature.
All of the materials required to construct this system are available from your local hardware store. There is no need to buy an overpriced hydroponic system unless you really want to or don’t have the time or ability to build your own. This system is simple to construct and tear down, as well as to store while not in use. The negatives to using this system are that the water temperature needs to be precisely maintained, as mentioned previously, and that the water must be properly oxygenated to keep the roots from being deprived at the bottom of the large bucket. Furthermore, if the water fails to circulate, plant death will rapidly occur. Plants left without water in this system can die in as little as one or two hours in hot environments. Growers wishing to plug in a system and leave it unsupervised should not build this type, as it requires daily supervision—not constant work and attention, just somebody to check to see if everything is working properly, i.e., if the water pump is working correctly, whether there are any leaks or clogged drippers or drains, and so on.
After harvest, the clay pellets are placed in a plastic garbage can with bleach and water and allowed to sit for 24 hours, at which point they are rinsed and ready to use again. The mesh baskets are reused as well. The whole system should be wiped off with hydrogen peroxide, and ONA cleaner (a bleach substitute) or Flora Kleen should be run through the drip line system and the rest of the system, allowing the whole thing to disinfect. After everything is rinsed with clean water the new plants are installed—ultimately, a short, hassle-free bit of work when compared to other systems. Remember, you don’t have to have an expensive system to get incredible buds.
Good example of a home-built aeroponic system from 1991.
This is a very good example of a typical aeroponic system. Home built, not store bought; anyone can build a system like this, but it requires a skilled grower to make it produce properly and maximize plant growth and yield. Growth rates and yield can be dramatically increased using aeroponic systems, but all environmental parameters and growth controls must be perfect in order to benefit from such a system.
The premise of aeroponics is that air (oxygen) and nutrient-enriched water are misted onto thriving plant roots. The roots absorb any oxygen, water, and nutrients they need at that particular moment and the remaining nutrients recirculate back to a reservoir to be re-aerated, temperature adjusted, and sent back to the plant roots to begin the process again. The mist is sprayed onto the plants’ roots with two (in case one gets clogged) four-gallon per hour misters, which are placed directly across from the roots, mounted in the side of six-inch PVC tubing. The tubes are capped at one end and joined at the other, draining into the common reservoir.
This system is not for somebody who wants to plug it in and leave it for long periods of time. It requires constant attention to make sure that misters aren’t clogged, the pH and PPM are correct, water and air temperatures are adjusted, and CO2 levels and water oxygen levels are optimum. This system requires multiple inspections each and every day; no “holidays.” Excess water temperature or a broken water pump will result in total and devastating crop failure.
Closet system set up for clone production.
Photos: K
Within reason, any space can be used to produce clones, as long as you monitor and control environmental factors such as temperature, humidity, and exposure to oxygen-rich air. In this case, a spare bedroom was used as well as the lower portion of the closet. The clones are under domes that retain moisture and humidity, and the temperature is kept up with a common household thermostatically-controlled air heater. If the humidity or temperature of the room exceeds desired levels, a humidistat-controlled filtered intake and exhaust fan will bring the levels back to acceptable ranges.
For small gardens, just the closet can be used to produce as many clones as you need, anytime you need them. A very small air heater, fluorescent lights, a humidity dome, and a few other items are all that you need. Three or four clones can easily be placed on the shelf on the top of the closet, in a small tray with a humidity dome, if you only need a few clones every once in a while.
Growtubes such as these can be used to construct many completely different hydroponic systems. Place misters in the side of them for aeroponics, or place drippers at each plant site for NFT tubes. You can also fill the growtubes with oxygenated, nutrient-treated water and use them as a deep water culture system. Finally, you can simply place rockwool in the mesh baskets and use the tubes as a periodic drip feed system.
Stack of growtubes to be cleaned.
Always have a clean and tidy electrical system.
Photos: Andre Grossman
A professional-quality electrical system is a must! Many growers are displaced or arrested every year because they overloaded electrical circuits or installed inferior wiring, timers, or other electrical components. The example you see here is small, simple, and professional. The ballasts, which are the white boxes at the bottom of the photo, plug into the power outlets that run to Intermatic timers (center of the photo) which are connected to a junction box that houses the main wiring and the wiring