50-ohm, 0.195-inch, coaxial cable with BNC connectorsRG-8, 50-ohm, 0.405-inch, coaxial cable with N connectorsRJ-6, 75-ohm, 0.242-inch, coaxial cable with BNC connectors108 Which of the following connector types are typically associated with Ethernet networks? (Choose all that apply.)F-typeBNCRJ-45DB-9N-type
109 Which of the following connector types was typically associated with a T-connector attached to the computer?RJ45MT-RJ8P8CBNCF
110 Which of the following connector types are associated with fiber-optic cables? (Choose all that apply.)RJ11STFLCMT-RJ
111 Which of the following types of cable, when installed, sometimes employed a device called a vampire tap?Unshielded twisted pairShielded twisted pairMultimode fiber opticSingle-mode fiber opticCoaxial
112 In an internal UTP cable installation, each horizontal cable run connects a wall plate in the work area to a centralized cabling nexus in a telecommunications room. Which of the following is the correct term for this cabling nexus?TelepoleDemarcBackbonePatch panelFiber distribution panel
113 Which of the following statements about single-mode and multimode fiber-optic cables are true?Single-mode cables can span longer distances than multimode cables.Single-mode cables are more resistant to electromagnetic interference than multimode cables.Single-mode cables are more difficult to install than multimode cables.Single-mode cables have a much larger core diameter than multimode cables.
114 Which of the following components are typically used only for telephone cable installations, and not for data networking? (Choose all that apply.)66 blocks110 blocks25 pair UTP cables100 pair UTP cables
115 Which of the following statements about single-mode fiber-optic cable are true? (Choose all that apply.)Single-mode cables use an LED light source, whereas multimode cables use a laser.Single-mode cables can span longer distances than multimode cables.Single-mode cables have a smaller core filament than multimode cables.Single-mode cables have a smaller bend radius than multimode, making them easier to install.Single-mode fiber-optic cables require a ground, whereas multimode cables do not.
116 Which of the following tools do cable installers use to connect bulk cable runs to wall plates and patch panels?A crimperA splicerA pigtailA punchdown block tool
117 Ralph has been hired by a client to install cabling to connect two existing networks. The two networks are in different buildings approximately 1000 feet apart. The cable type must support Gigabit Ethernet data rates of 1000 megabits per second (Mbps) and provide a high level of resistance to electromagnetic interference (EMI). Your client wants the most economical cabling solution that meets their needs. Which of the following cable types best meets the needs of this client?Multimode fiber-optic cableShielded Twisted Pair (STP) cableUnshielded Twisted Pair (UTP) cableThin coaxial cableSingle-mode fiber-optic cable
118 Which of the following are connector types used with coaxial cables? (Choose all that apply.)BNCF-typeN-typeSTRJ-11
119 Alice has been hired by a corporation to design the cabling for their network. The corporation just moved into two different floors of an older building: a retail space on the ground floor and an office space on the 43rd floor. The building has existing Category 5 (CAT5) Unshielded Twisted Pair (UTP) cable. Alice's client wants two separate Local Area Networks (LANs), one on each of the two floors, with a backbone network connecting them. They want a 1 gigabit-per-second (Gbps) data rate for each LAN but plan on migrating to 10 Gbps in the future. The two networks are approximately 200 meters apart. Which of the following solutions best meets the client's needs?Install Category 6 (CAT6) or Category 6a (CAT6a) UTP cable for the LANs. These cables run at 1 Gbps and provide a migration path to 10 Gbps. Use twisted pair cable for the backbone network.Use the existing CAT5 cabling for the LANs, since CAT5 runs at 1 Gbps. Use thick coaxial cable for the backbone network.Install CAT6 or CAT6a UTP cable for the LANs. These cables run at 1 Gbps and provide a migration path to 10 Gbps. Use multimode fiber-optic cable for the backbone network.Install CAT6 or CAT6a UTP cable for the LANs. These cables run at 1 Gbps and provide a migration path to 10 Gbps. Use the existing CAT5 cable for the backbone network.
120 A maintenance worker, while replacing a light fixture in an office building, accidentally severs a network cable in the drop ceiling. The tenants use a variety of Local Area Network (LAN) technologies throughout the structure, but on that particular floor, there are three separate LANs: a 10-node Thin Ethernet LAN using coaxial cable in a bus topology, a 25-node Gigabit Ethernet LAN using twisted pair cable in a star topology, and a 5-node Fiber Distributed Data Interface (FDDI) LAN using multimode fiber-optic cable in a double ring topology. Without knowing which of the LANs the severed cable belongs to, what is the maximum number of computers that could be directly affected by the cable break?015102540
121 In the punchdown process for Unshielded Twisted Pair (UTP) cable, which of the following is the last step that you perform when connecting bulk cables to jacks in wall plates and patch panels?Cut off the excess wire that protrudes past the contacts.Press the bare wire down between the two metal contacts that hold it in place.Strip some of the insulating sheath off the cable end to expose the wires.Insert the wires into the appropriate contacts in the jack.Strip a small amount of insulation off each wire.Separate the twisted wire pairs at the ends.
122 Which of the following cable connector types is not used with fiber-optic cable?Straight Tip (ST)Subscriber Connector (SC)Mechanical Transfer–Registered Jack (MT-RJ)F-typeFiber Local Connector (LC)
123 Which of the following twisted pair cable types can you use to construct a 10GBase-T network with 100-meter segments? (Choose all that apply.)CAT5CAT5eCAT6CAT6aCAT7CAT8
124 Which of the following cable connector types have been rendered nearly obsolete by Universal Serial Bus (USB) connections? (Choose all that apply.)BNCRJ-11DB-9DB-25
125 Which of the following twisted pair cable types is rated for both a 10-megabit-per-second (Mbps) data rate (using two pairs) and a 100 Mbps data rate (using four pairs)?Category 3 (CAT3)Category 5 (CAT5)Category 5e (CAT5e)Category 6 (CAT6)
126 Ed has been hired to install network cabling for a small private company with 15 employees who need to share files and printers. All of the employees are physically located within the same building in two separate office spaces directly adjacent to each other, sharing a common wall and door for access. Both offices have drop ceilings. The client wants a simple Gigabit Ethernet installation that is easy to troubleshoot. In addition, Ed's client wants to keep installation costs to a minimum. Which of the following combinations of topology, cable type, and installation method would best meet the needs of Ed's client?Star topology, fiber-optic cabling, and internal installationBus topology, coaxial cabling, and external installationBus topology, twisted pair cabling, and internal installationStar topology, coaxial cabling, and external installationStar topology, twisted pair cabling, and external installation
127 Which of the following cable types are typically used in newly constructed Local Area Network (LAN) installations? (Choose all that apply.)Single-mode fiber opticMultimode fiber opticCoaxialUnshielded twisted pair
128 Which of the following statements are true about coaxial cable? (Choose all that apply.)Coaxial cable has three conductors within the same sheath.Coaxial cable has two conductors within the same sheath.Coaxial cable has a copper core that carries light pulse signals.Coaxial cable has a copper core that carries electrical signals.Coaxial cable has an insulating outer sheath made of braided strands.Coaxial cable has an insulating sheath made of either PVC or Teflon.
129 Which of the following twisted pair cable types are rated for 1000 megabit-per-second (Mbps) Gigabit Ethernet using two wire pairs? (Choose all that apply.)Category 3 (CAT3)Category 5 (CAT5)Category 5e (CAT5e)Category 6 (CAT6)Category 6a (CAT6a)None of the above
130 Which of the following twisted pair cable types support both
