a metal clamp with an electrically insulated outside shell for the welder to hold safely.
The heat of the arc causes both the core wire and the flux covering at the electrode tip to melt off as droplets. The molten metal collects in the weld pool and solidifies into the weld metal. The lighter molten flux, on the other hand, floats on the pool surface and solidifies into a slag layer covering the weld metal.
1.3.1.1 Functions of Electrode Covering
The covering of the electrode contains various chemicals and even metal powder in order to perform one or more of the functions described below:
Protection. The electrode covering provides a gaseous shield to protect the molten metal from air. For a cellulose‐type electrode, the covering contains cellulose, (C6H10O5)x. A large volume of gas mixture of H2, CO, H2O, and CO2 is produced when cellulose in the electrode covering is heated to decompose. For a limestone‐ (CaCO3‐) type electrode, on the other hand, CO2 gas and CaO slag form when the limestone decomposes. The limestone‐type electrode is a low‐hydrogen‐type electrode because it produces a gaseous shield low in hydrogen. It is often used for welding metals that are susceptible to hydrogen cracking, such as high‐strength steels.
Deoxidation. The electrode covering provides deoxidizers and fluxing agents to deoxidize and cleanse the weld metal. The solid slag formed also protects the already solidified but still hot weld metal from oxidation.
Arc stabilization. The electrode covering provides arc stabilizers to help maintain a stable arc. The arc is an ionic gas (a plasma) that conducts the electric current. Arc stabilizers are compounds that decompose readily into ions in the arc, such as potassium oxalate and lithium carbonate. The potassium and lithium ions increase the electrical conductivity of the arc and help the arc conduct the electric current more smoothly.
Metal addition. The electrode covering provides alloying elements and/or metal powder to the weld pool. The former helps control the composition of the weld metal while the latter helps increase the deposition rate.
1.3.1.2 Advantages and Disadvantages
The welding equipment is relatively simple, portable, and inexpensive as compared to other arc welding processes. For this reason, SMAW is often used for maintenance, repair, and field construction. However, the gas shield in SMAW is not clean enough for reactive metals such as aluminum and titanium. The deposition rate is limited by the fact that the electrode covering tends to overheat and fall off if excessively high welding currents are used. The limited length of the electrode (about 35 cm) requires electrode changing, and this further reduces the overall production rate.
1.3.2 Gas–Tungsten Arc Welding
1.3.2.1 The Process
GTAW is a process that melts and joins metals by heating them with an arc established between a nonconsumable tungsten electrode and the metals, as shown in Figure 1.12. For this reason, welding can be accomplished either with or without a filler metal. When a filler rod is needed, for instance, for joining thicker materials, it can be fed either manually or automatically into the arc. In most other arc welding processes, the electrode itself is a filler wire.
Figure 1.12 Gas–tungsten arc welding: (a) overall process; (b) welding area enlarged.
The torch holding the tungsten electrode is connected to a shielding gas cylinder, as well as one terminal of the power source. The tungsten electrode is usually in contact with a water‐cooled copper tube, called the contact tube, which is connected to the welding cable (cable 1) from the terminal. This allows both the welding current from the power source to enter the electrode and the electrode to be cooled to prevent overheating. The workpiece is connected to the other terminal of the power source through a different cable (cable 2). The shielding gas goes through the torch body and is directed by a nozzle toward the weld pool to protect it from the air.
Protection of the liquid metal is much better in GTAW than in SMAW because an inert gas such as argon or helium is usually used as the shielding gas and because the shielding gas is directed toward the weld pool. For this reason, GTAW is also called tungsten–inert gas (TIG) welding. However, in special uses, a noninert gas can be added in a small quantity to the shielding gas. Therefore, GTAW seems a more appropriate name for this welding process.
1.3.2.2 Polarity
Figure 1.13 shows three different polarities in GTAW [5], which are described next:
1 Direct‐current electrode negative(DCEN). This, also called the straight polarity, is the most common polarity in GTAW. The electrode is connected to the negative terminal of the power supply. As shown in Figure 1.13a, electrons are emitted from the tungsten electrode and accelerated while traveling through the arc. A significant amount of energy, called the work function, is required for an electron to be emitted from the electrode. When the electron enters the workpiece, an amount of energy equivalent to the work function is released. This is why in GTAW with DCEN more power (about two‐thirds) is located at the workpiece end of the arc and less (about one‐third) at the electrode end. Consequently, a relatively narrow and deep weld can be produced.
2 Direct‐current electrode positive(DCEP). This is also called the reverse polarity. The electrode is connected to the positive terminal of the power source. As shown in Figure 1.13b, the heating effect of electrons is now at the tungsten electrode rather than at the workpiece, thus producing a shallow weld. Furthermore, a large‐diameter, water‐cooled electrode is preferred in order to prevent the electrode tip from melting. The positive ions of the shielding gas bombard the workpiece, as illustrated in Figure 1.14, knocking off oxide films and producing a clean weld surface. Therefore, DCEP can be used for welding thin sheets of strong oxide‐forming materials such as aluminum and magnesium, where deep penetration is not required.
3 Alternating current (AC). Reasonably good penetration and oxide cleaning action can both be obtained, as illustrated in Figure 1.13c. This is often used for welding aluminum alloys.
Figure 1.13 Three different polarities in GTAW.
Figure 1.14 Surface cleaning action in GTAW with DC electrode positive.
1.3.2.3 Electrodes
