Banjo For Dummies. Bill Evans
Чтение книги онлайн.
Читать онлайн книгу Banjo For Dummies - Bill Evans страница 15
![Banjo For Dummies - Bill Evans Banjo For Dummies - Bill Evans](/cover_pre848569.jpg)
1 Pick the 4th string fretted at the 5th fret and compare its pitch to the open 3rd string.You may need to strike the fretted 4th string first, wait a moment to hear its pitch, and then strike the 3rd string to listen to its pitch. Does the 3rd string (the second note you play) sound higher or lower than the 4th string? Try singing the two pitches to feel whether the pitch rises or falls.
2 Using the tuning peg, adjust the pitch of the 3rd string up or down until it matches the pitch of the fretted 4th string.When the pitches of the two strings match each other, the 4th and 3rd strings of your banjo are in tune.
3 Pick the 3rd string fretted at the 4th fret and match the open 2nd string to this sound.After these strings sound the same, you have the 4th, 3rd, and 2nd strings of your banjo in tune.
4 Pick the 2nd string fretted at the 3rd fret and tune the open 1st string to this sound.
5 Pick the 1st string fretted at the 5th fret and tune the open 5th string to this sound.Remember that the 5th string is the short string on your banjo that's located on the opposite side of your neck from the 1st string. Some banjos have 5th-string tuning pegs that are difficult to turn without causing wild fluctuations in pitch. Don't worry if it takes a bit more time to get the 5th string in tune.
Even if you follow my instructions carefully, I'm sure that you may discover the following frustrations when tuning the banjo in this way (but don't “fret” — you aren't alone):
Your reference point is always a fretted string when tuning from a lower- to a higher-pitched string. You need to lift the left hand up to adjust the tuning peg of the string you're attempting to tune and then fret it again on the lower string to play the reference pitch.
If you make a slight error at the beginning of this process, that mistake is exaggerated as you proceed to try and tune the rest of the strings. You may have to start all over.
Reference Tuning: Getting a Little Outside Help
Relative tuning is great when you're playing by yourself or for quickly touching up a string or two in the middle of a practice session. However, when playing with others (or with the audio tracks and video clips that accompany this book, available at www.dummies.com/go/banjo
), you need to get accustomed to tuning your banjo using one or more outside reference notes as provided by an electronic tuner or another instrument. I explain how to tune by using reference notes in the following sections.
Using an electronic tuner
Tuners provide a reference point for you to tune individual strings one at a time. These days, a tuner is pretty much an essential accessory to carry with you wherever you take your banjo. When you play a string, the tuner “hears” the note and gives an indication of the note's pitch by showing a letter name for the note closest to it in pitch, with an accompanying ♯ (sharp) or ♭ (flat) sign, if needed (for instance, if the note you're playing is closest to an F♯ in pitch, the tuner reads F♯). The tuner also indicates whether your string is sharp (too high) or flat (too low) in relation to your reference note via a meter or a row of small LED lights. (Check out Chapter 14 for a discussion of how tuners work and of the different types of tuners currently available.) An electronic clip-on tuner is shown in Figure 2-2.
Photograph courtesy of Elderly Instruments
FIGURE 2-2: Using an electronic clip-on tuner makes tuning easier.
G / G♯ or A♭ / A / A♯ or B♭ / B / C / C♯ or D♭ / D / D♯ or E♭ / E / F / F♯ or G♭ / G
Here are a few tidbits of info that may help you better understand this series of notes and how they relate to tuning your banjo:
Equivalent notes: You may notice that some notes in the preceding series have an or between them. Without getting too boring, just remember that a G♯ is the same pitch as an A♭, an A♯ is the same as a B♭, and so on. These equivalent notes are found at the same fret on your fingerboard.
Pitch: As you move to the right in the order of notes, you're naming higher-pitched notes; as you move to the left, the notes are lower pitched.
Half versus whole steps: If you move one note