when they are really trying to make the leaf-shaped blade."195 The handicraftsmen of the Smithsonian Institute have not been able to make a leaf-shaped blade such as may be seen in the museums, and no Indian has been found who could make one. "This is one of the lost arts."196 Other pieces of rude form have been set aside as chips, or rejects, but such are found in use as scrapers, or in handles, and are to be recognized as products which belong to the series.197 Some rude implements found in the hill gravels of Berkshire, England, have been offered as anterior to the paleolithic implements as usually classified.198 Lubbock said that he could not find in the large Scandinavian collections "a single specimen of a true paleolithic type."199
128. Forms of stone axes. Stone axes are found all over the globe. Chipped, sharpened, polished, grooved, pierced, handled, are different kinds which may be set in a series of advancing improvement, and under each grade local varieties may be distinguished, but the art is essentially the same everywhere. "Probably no discovery is older than the fact that friction would wear away wood or bone, or even stone."200 It was also learned that rawhide and sinew shrank in drying, and this fact was very ingeniously used to attach handles, the sinew or membrane being put on while fresh and wet. American stone axes are grooved to receive a handle made by an ingenious adaptation of roots and branches with pitch or bitumen. "Bored stone axes are found in the tropical regions of America. Although they are very rare, they are well executed."201 The device of boring stone axes appears at the end of the stone age in the lake dwellings of Switzerland. Perhaps they were only decorative.202 The Polynesians used stone axes which were polished but not bored or grooved, and the edge was not curved.203 The Pacific islanders clung to the type of the adze, so that even when they got iron and steel implements from the whites they preferred the knife of a plane to an ax, because the former could be used adze-fashion.204 In the stone graves of Tennessee have been found implements superior to all others found in the United States in size, variety, and workmanship. Amongst these are a flint sickle-shaped tool, axes a foot long or more, a flint sword twenty-two inches long, a flint needle eight inches long; also objects supposed to be for ceremonial or decorative use. Stone axes with handles all in one piece have been found in Tennessee, Arkansas, and South Carolina.205
129. How stone implements are made. What was the process by which these stone implements were made? The artifacts bear witness directly to two or three different operations, separate or combined, and to a great development of the process. As above stated, Tasmanians, after they became known to Europeans, made stone implements as they needed them, giving to a stone a rude adaptation to the purpose by chipping off a few flakes. Short sharp blows were struck by one stone upon another. The blow must, however, fall upon just the right spot or it would not produce the desired result. Therefore the flakes were often thrown off by pressure. A stick or horn was set against the spot where the force should be applied, and braced against the breast of the operator, while he held the stone between his feet. This latter operation is described as used by the Mexicans to get flakes of obsidian.206 By carrying further the process of chipping or pressing the stone could be shaped more perfectly, and by rubbing it on another stone it could be given a cutting edge. The rubbing process could also be applied to the surface to make it smooth instead of leaving it as it was after the flaking process. The processes of striking and pressing were also combined. The pebble was broken by blows and the pieces were further reduced to shape by the pressing process. Different devices were also invented for holding the stone securely and in the proper position. Skill and judgment in perceiving how and for what purpose each pebble could best be treated was developed by the workers, and division of labor arose amongst them as some acquired greater skill in one operation and others in another. The operations of pressing and striking were also made complex in order to accomplish what was desired. A sapling was cut off so that the stump of a limb was left at the bottom of it. It was set against the spot where the force was needed, and a blow struck in the crotch of the limb caused the chip to fly. This apparatus was improved and refined by putting a horn tip on the end point of contact. Another device was to cut a notch in a tree trunk, which could be used as a fulcrum. A long lever was used to apply the pressure to the stone laid at the root of the tree, or on the horizontal space at the bottom of the notch.207 These variations show persistent endeavor to get control of the necessary force and to apply it at the proper point with the least chance for error and loss. Buckley reported about the "tomahawks" of the aborigines of Victoria, that the stone was split into pieces, without regard to their shape, but of convenient thickness. A piece was rubbed on rough granite until "it is brought to a very fine thin edge, and so hard and sharp as to enable them to fell a very large tree with it." The handles are "thick pieces of wood, split and then doubled up, the stone being in the bend and fixed with gum, very carefully prepared for the purpose, so as to make it perfectly secure when bound round with sinews."208 The natives of the Admiralty Islands use obsidian which is dug from layers in the ground. Only a few know the art of making axes, and they prosecute it as a means of livelihood. Skill is required especially to judge of the way in which the stone will split. The only tool is a stone with which light, sharp blows are struck.209 The axes of the Swiss lake dwellings were made from bowlders of any hard stone. By means of a saw of flint set in wood, with sand and water, a groove was cut on one side and then on the other. With a single blow from another stone the bowlder was made to fall in two. By means of a hard stone the piece was rudely shaped and then finished by friction. A modern student has made such an ax in this way in five hours. Sometimes the stone was set in a handle of wood or horn.210 It will be noticed that this process was not possible until an auxiliary tool, the flint saw, had already been made. The tools and processes were all rude and great skill and dexterity were required in the operator. "Lafitau says the polishing of a stone ax requires generations to complete. Mr. Joseph D. McGuire fabricates a grooved jade ax from an entirely rough spall in less than a hundred hours."211
130. How arrowheads are made. As to arrowheads, "there are a dozen or more authentic reports by eye-witnesses of the manufacture of arrowheads in as many different ways."212 The California Indians broke up a piece of flint or obsidian to the proper-sized pieces. A piece was held in the left hand, which was protected by a piece of buckskin. Pressure was put upon the edge by a piece of a deer's antler, four to six inches long, held in the right hand. In this way little pieces were chipped off until the arrowhead was formed. Only the most expert do this successfully.213 Sometimes the stone to be operated on is heated in the fire, and slowly cooled, which causes it to split in flakes. A flake is then shaped with buck-horn pincers, tied together at the point with a thong.214 In another report it is the stone with which the operation is performed which is said to be heated.215 In a pit several hundred flint implements were found stored away in regular layers with alternate layers of sand between. Perhaps the purpose was to render them more easy to work to the desired finish.216
