provided this objective map to help you locate where the objectives for the CCNA Routing and Switching certification Exam 200-125 are covered in each chapter. Please refer to it when you want to find an objective quickly.
Exam objectives are subject to change at any time without prior notice and at Cisco's sole discretion. Please visit Cisco's certification website (www.cisco.com/web/learning) for the latest information on the CCNA Routing and Switching certification.
Assessment Test
1. You reload a router with a configuration register setting of 0x2101. What will the router do when it reloads?
A. The router enters setup mode.
B. The router enters ROM monitor mode.
C. The router boots the mini-IOS in ROM.
D. The router expands the first IOS in flash memory into RAM.
2. Which of the following commands provides the product ID and serial number of a router?
A. show license
B. show license feature
C. show version
D. show license udi
3. Which command allows you to view the technology options and licenses that are supported on your router along with several status variables?
A. show license
B. show license feature
C. show license udi
D. show version
4. You want to send a console message to a syslog server, but you only want to send status messages of 3 and lower. Which of the following commands will you use?
A. logging trap emergencies
B. logging trap errors
C. logging trap debugging
D. logging trap notifications
E. logging trap critical
F. logging trap warnings
G. logging trap alerts
5. IPv6 unicast routing is running on the Corp router. Which of the following addresses would show up with the show ipv6 int brief command?
Corp#sh int f0/0
FastEthernet0/0 is up, line protocol is up
Hardware is AmdFE, address is 000d.bd3b.0d80 (bia 000d.bd3b.0d80)
[output cut]
A. FF02::3c3d:0d: bdff: fe3b:0d80
B. FE80::3c3d:2d: bdff: fe3b:0d80
C. FE80::3c3d:0d: bdff: fe3b:0d80
D. FE80::3c3d:2d: ffbd:3bfe:0d80
6. A host sends a type of NDP message providing the MAC address that was requested. Which type of NDP was sent?
A. NA
B. RS
C. RA
D. NS
7. Each field in an IPv6 address is how many bits long?
A. 4
B. 16
C. 32
D. 128
8. What does the command routerA(config)#line cons 0 allow you to perform next?
A. Set the Telnet password.
B. Shut down the router.
C. Set your console password.
D. Disable console connections.
9. Which two statements describe the IP address 10.16.3.65/23? (Choose two.)
A. The subnet address is 10.16.3.0 255.255.254.0.
B. The lowest host address in the subnet is 10.16.2.1 255.255.254.0.
C. The last valid host address in the subnet is 10.16.2.254 255.255.254.0.
D. The broadcast address of the subnet is 10.16.3.255 255.255.254.0.
E. The network is not subnetted.
10. On which interface do you configure an IP address for a switch?
A. int fa0/0
B. int vty 0 15
C. int vlan 1
D. int s/0/0
11. Which of the following is the valid host range for the subnet on which the IP address 192.168.168.188 255.255.255.192 resides?
A. 192.168.168.129–190
B. 192.168.168.129–191
C. 192.168.168.128–190
D. 192.168.168.128–192
12. Which of the following is considered to be the inside host's address after translation?
A. Inside local
B. Outside local
C. Inside global
D. Outside global
13. Your inside locals are not being translated to the inside global addresses. Which of the following commands will show you if your inside globals are allowed to use the NAT pool?
ip nat pool Corp 198.18.41.129 198.18.41.134 netmask 255.255.255.248
ip nat inside source list 100 int s0/0 Corp overload
A. debug ip nat
B. show access-list
C. show ip nat translation
D. show ip nat statistics
14. How many collision domains are created when you segment a network with a 12-port switch?
A. 1
B. 2
C. 5
D. 12
15. Which of the following commands will allow you to set your Telnet password on a Cisco router?
A. line telnet 0 4
B. line aux 0 4
C. line vty 0 4
D. line con 0
16. Which
